In Wyoming, every engineer is required to have a state seal or rubber stamp, acquired at his or her own expense, to apply to all paperwork. The stamp or seal must conform to the rules and regulations that are sent out by the Engineering Board in the State of Wyoming.
The Wyoming PE Seal Requirements
In Wyoming, there is some flexibility as to the type of device you can use – either seals or rubber stamps are acceptable. The measurements must meet strict specifications, though. The seal or stamp must measure 1-3/4" on the outside, and 1-1/4" on the inside. On the seal, you will see two concentric circles. On the upper portion of the seal, the phrase “Professional Engineer” will appear between the two circles. On the lower portion, at the bottom of the annular space, appears the name of the state. The inner circle contains the licensee’s name and number, along with the date. The licensee number is centered in the inner portion of the seal, and should not be larger than the name.
Using the Seal or Stamp on Documents
On any documents that you must file, there must be an imprint of your Wyoming PE embosser seal. This is either the original seal or a rubber stamp facsimile. You have to seal any documents, plans, drawings, sketches, plats, or other types of work products, whether you are submitting them to a client, or the State of Wyoming. The seal or stamp must also appear on any original or non-original copies, as well as on any tracings. Seals that have been created using CAD equipment are acceptable, but they must be accompanied by an original, dated signature of the person who has prepared the document. Any computer-generated seals must also comply with the requirements outlined in the previous section.
Your Wyoming PE embosser seal or stamp may appear only on work that is under your exclusive control. This means either work that you have done, or that has been done under your direct supervision. If you are found to have used the seal or stamp on work that was not under your direct control, you may be subject to disciplinary action by the Board.
Please note that if you are licensed as a surveyor as well as an engineer, you will require seals or stamps for both disciplines.
Misuse of Professional Engineer Stamps
In addition to disciplinary action, if you have misused the seal, you can also be held liable if someone else does so without your knowledge. If your seal is lost or has been stolen, you must report this to the Board immediately. Otherwise, you could be held legally responsible for any damage due to faulty work done under your seal between the time you noticed it missing and the time that you reported this to the Board. And again, you could face disciplinary action. Never delay reporting a missing seal.
Wyoming Professional Engineer Stamp & Seal Products Available
Engineer Seal Stamps.com has Wyoming PE embossers and seals you need to be fully compliant with Wyoming law, including:
- Handheld seal embossers
- Max light pre-inked stamps
- Soft seal embossers
- Slim pre-inked stamps
- Long-reach seal embossers
- Self-inking stamps
- Regular hand rubber stamps
- Extended long-reach seal embossers
- Desk seal embossers
- Any rubber stamp or embossing seal
You can obtain further information about compliance with sealing requirements for Wyoming engineers by visiting the Wyoming Board of Engineers website.
Snippet for three equal columns
Self Inking Stamps
Looking for an easy and efficient way to keep your Wyoming PE Stamp up to date? Look no further than the Self-Inking Wyoming PE Stamp! State Board Approved and including a free electronic seal, this product is guaranteed to meet your specifications. With 6 file types included (DXF, DWG, TIF, JPG, PDF, and PNG), you can use this product in a variety of ways. This self-inking stamp offers simple press and print stamping which is perfect for repetitive stamping, with up to 5,000 impressions before needing to be re-inked. The internal ink pad is also replaceable, making this product long-lasting and cost-effective. Choose from 11 different ink colors to get the perfect look for your needs. Select your ink color and order your self-inking stamps today.
Pre-Inked Stamps
Looking for an engineering stamp that is sure to meet your state board specifications? Look no further than the Pre-Inked Wyoming Engineering Stamp! This impressively detailed stamp comes in 5 ink colors and includes an electronic seal. It also works in a press and print manner, making it simple to use. Best of all, there is no ink pad to replace – the die plate absorbs ink, making for clean and quiet stamping. Want to see what the stamp looks like before it is made? You can add a pdf proof to your order so you can review it and make changes before your engineer stamp ships out. So why settle for anything less than the best? Get your hands on a Wyoming Engineering Stamp today!
About ESS
At ESS, we have every templated for every state made to the applicable regulations for the Wyoming Board of the board for your state. If you need a professional seal, we will make it quickly and correctly. Order your engineer seals from ESS today.
